激光切割機冬天使用注意事項

我們冬天在使用激光切割機的時候應該注意哪些問題：
一. 循環水, 1個月至少換一次,換水是把水泵中的過濾海綿也拿出來清洗一次.
二. 軌道上油,1個月至少上一次油,上油前先把過道擦洗干凈.
三. 蜂窩板下面,定期清理,防止碎布片多后導致起火.
四. 冰凍天氣,注意激光管內的水可能會結冰,導致激光管破裂,顧,在冰凍天氣,不工作的時候,要么把激光管內的水放出,要么把水泵24小時開通,保持水流24小時,這樣不會被冰凍.
五. 擦洗鏡片,1個星期擦洗一次,如果干凈可以不擦,但每個星期必須檢查一次.擦洗鏡片是注意不要動反光鏡后面的3個銅螺絲,且聚焦鏡不能裝反,最終是凹面向下,凹面才能聚光,如果裝反就散光,切出來的線條很粗,且切不透.
六. 安全事項,小孩和非操作人員不得擅自接觸機器,以防以外,2號反光鏡與3號反光鏡之間的那條線是有光區,切勿在工作是接觸此區域,雷雨天機器最好聽掉,切斷電源
七。如果您的工廠或車間在節日期間長時間放假、機床不運行。一定要注意機床的冬季保溫處
理。一定要將冷水機的水、激光器、切割頭、鏡片、的水全部放掉，防止結冰導致機床損壞。

   打開冷水機的放水閥，將水全部放出。將過濾芯取出排水，因這部分水是無法排出的防止結冰將
外殼漲破。對一些不易排出的水需要用壓縮空氣吹除，為了防止水倒流進激光器內部、損壞激光器內
部的精密傳感器。務必關閉全部水閥門。

1.關閉冷水機的全部閥門。
2.打開排水閥門。將水箱的水全部放掉。
3.打開全部水冷機的過濾器，將無法排出的水倒了。
4.去離子桶的接頭打開，用氣將桶內無法排出的水吹出。切忌用高壓氣體，壓力控制在
1~2公斤左右。
5.將高壓泵內部的水排出。打開排氣閥門，用氣吹除。水會回流到排水孔流出。此處的水如果不排出
會將泵體漲壞，高壓表漲破。
6.  以上步驟完成以后，將全部的接頭安裝還原。雖然已經做了以上處理，依然不可以掉以輕心。溫
度過低依然會將制冷回路、壓縮機、散熱片、熱交換器等凍壞。保持環境溫度在5℃以上，可以有效地保護機器。

文章來源：（http://jsbfxx.cn ）

A circulating water, 1 months at least once, change the water is to filter sponge in water pump also take out for cleaning time
Two. Track oiling, once at least 1 months of oil, oil before the first aisle clean
Three. Honeycomb board below, regular cleaning to prevent pieces of cloth, after the cause of the fire
Four. Freezing weather, pay attention to the laser tube water may freeze, causes the laser tube rupture, Gu, in freezing weather, when not working, or to the laser tube water release, or the pump 24 hours a day, keep the water 24 hours, so it does not freeze
Five. Scrubbing lenses, 1 weeks is swabbed, if can not wipe clean, but each week to check again. Scrubbing lenses are 3 copper screws do not move the mirror behind, and the focusing mirror can not be anti loaded, the final is concave downward, concave to spot, if installed anti is astigmatism, cut out the lines very coarse, and don't know
Six. Safety, child and non operating personnel are not allowed to touch the machine, in order to prevent the outside, the line between the 2 reflector and 3 reflector is light, do not touch this area is in work, the thunderstorm days machine better off, cut off the power supply
Seven. If the machine is your factory or workshop during the festival long time holiday, do not run. Attention must be paid to the winter heat preservation office machine
Science. It must be cold water machine, water, laser cutting head, lens, the water drain off, to prevent freezing caused damage to the machine.
Drain valve open cold water machine, all the water out. Will filter out drainage, because this part of the water is not drained to prevent freezing will
The shell burst. The compressed air blowing need some difficult to discharge water, in order to prevent the water poured into the cavity, the laser damage
Department of precision sensor. Be sure to close all the water valve.
1 close all valves cold water machine.
2 open the drain valve. The water tank water drain off.
3 open all water-cooled machine filter, will be unable to drain the water out.
Joint 4 deionized bucket opened, gas will be unable to drain the water in the barrel to blow out. High pressure gas should not, under the control of the pressure
1~2 kg.
5 for the high-pressure pump internal water discharge. Open the exhaust valve, gas blowing. The water will flow to the drainage hole outflow. Here the water is not discharged if
Will pump up bad, high surface burst.
After the above 6 steps, all joint installation reduction. Although it has been done above, still can not let down. Temperature
Through the low will continue cooling loop, compressor, radiator, heat exchanger, frozen. Keep the environment temperature at 5 ℃, can effectively protect the machine.

新聞、技術文章、資料下載網站聲明
資料編輯人：admin

電話：

• 北京激光切割加工的原理分析

  2024-01-10

• 2016年春節德航隆工激光切割加工開工通知

  2016-02-20

• 北京德航隆工承接各種材質激光切割加工業務

  2015-06-23

• 不銹鋼切割的過程中容易出現的問題

  2014-08-26

• 想要開不銹鋼加工廠應該準備或注意什么

  2014-08-14